How Can I Put My Fingerboard Trucks On So They Don't Fall Off?
Tiny screws and a tiny tool can make putting trucks on a fingerboard tricky. If the screws don't go in right, the trucks can work loose and fall off while you ride. Here's how to mount them so they stay put.
Start every screw lightly in an X pattern (top left, then bottom right, and so on), check that the truck sits flat against the deck with no gap, then tighten them all. If a screw won't sit right, take it out and put it back in. For extra-thick decks or riser pads, use longer 6mm screws.
1. Screw in an X pattern
The order you put your screws in makes a difference. Each truck has four holes. Start with the top left, then go to the bottom right, then the other two, in an X. This keeps the truck even under the deck and makes crooked screws less likely. If you crank the top two screws all the way down first, the bottom of the truck can lift, and the bottom two won't go in evenly.
2. Screw in lightly, then tightly
Put all four screws in lightly first, following the X pattern, and check that the truck is sitting flush. Once it's flush, tighten them all the way. This makes sure the truck is flat before anything gets locked down.
3. Check that the trucks sit flat
Flip your board over and look at the trucks from the side. There shouldn't be any gap between the deck and the bottom of the truck. If one side isn't flat, find the screw causing it, take it out and carefully put it back in.
4. Check your deck thickness and screw length
Our standard screws fit all Teak Tuning decks, but they may not reach through decks that are thicker than standard or trucks mounted on riser pads. Our stainless steel fingerboard screws come in Long (5mm) and Extra Long (6mm). Use the 6mm screws with riser pads or extra-thick decks.
Careful with already-threaded holes. Many truck holes come unthreaded, and the screws cut the threads as they go in. If you put a screw into a threaded hole at an angle, you can cross-thread it and ruin the hole. Go slowly and keep the screw straight.
5. Use a tool that's easy to grip
Teak trucks and completes come with a mini fingerboard tool, and it gets the job done. If you have larger or shaky hands, or you're new to working with small parts, a bigger tool makes setup a lot easier:
- Repair and Tool Kits: two large handle tools with interchangeable bits. They're slightly magnetic, so they pick up tiny screws, and they come in a case.
- Pro Fingerboard Tool: shaped like a real skate tool, with a screwdriver on one end, a nut driver on the other and a grooved handle for grip.
- Complete Builder Vise: a steady "third hand" that clamps your deck with non-scratch jaws and has truck centering fixtures to line your trucks up while you screw them on.
FAQ
Why do my fingerboard trucks keep falling off?
Usually the screws went in crooked or uneven, so the truck isn't sitting flat. Take the screws out, start them lightly in an X pattern, check for a gap, then tighten.
What order should I put fingerboard screws in?
An X pattern. Start top left, then bottom right, then the other two. Put them all in lightly first, then tighten.
What size screws do I need with riser pads?
Longer ones. Use our Extra Long (6mm) screws with riser pads or extra-thick decks. Every Teak riser pad kit also includes 8 extra long screws.
I cross-threaded a hole. Can I fix it?
Our longer screws are a fraction larger in diameter, so they can rethread a hole that's been cross-threaded. Go slowly and keep the screw straight.
What tool do I need to put trucks on?
A fingerboard tool that fits the truck screws and locknuts. Teak trucks and completes include a mini tool, and our Repair and Tool Kits have bigger handles that are easier to grip.

I ordered a complete fingerboard set and I can’t get the screws out so that I can put the grip tape on. What should I do?
Hello. So my fi gerboard is amazing except for one thing. The truck keeps falling off. I have taken it off and done the x pattern and everything. It’s tight for a bit then the truck just Flys off.
I received mine today April 5 and am having a really hard time screwing my trucks on. They won’t screw in and no matter how hard I turn them they won’t go in. It shouldn’t be this hard to do. If the trucks were threaded this would be much easier
Since there’s five bubble bushing in each set, if you buy four sets you get one set free!
Leave a comment